Place the spool on the SlXX l pin with Spool holder follow the instuctions on previous page. The thread shall reel clockwise. Push the spool pin hack in. Hold the thread near the spool using 5 right hand. I se your left hand to bring the end of the thread in the direction of the arrow on the 6 machine. Place the thread under the presser foo and into the thread cutter, pull downwards to cut it. A small hxk vill pass through the needle 3 Place the thread around the guide a I and under the flanges in front of the needle, so the thread catches into the small hook.
The h xk pulls the thread through the needle eye and forms a loop behind the needle, Pull the thread loop out behind the needle.
S Place the thread tinder the presser foot and cut the thread. Thread the left needle. Place the large spool holder and a felt pad on the spool pin.
S Place the thread spool or the bobbin with the second thread on the spool 6 lhread the machine as before but this thread should lie between the outer thread tension discs, and out side the last thread guide.
Thread the right needle. Push the bobbin spindle down. Note: t epending on thread quality, take the thread one or two turns around the is ililan thread tensi in guide a 4 From above wind a few turns of thread clockwise around the bobbin and into the thread cutler d. When the bobbin is full, the winding will stop automatically. Remove the bobbin and cut off the thread. Bring the bobbin spindle up. Bring the thread into the thread ten guide a. Pbcing the Bobbin in the Machine I Remove the bobbin coer by sliding it towards v L1 2 Place the bobbin in the bobbin case with the mark facing up and the thread to the left of the bobbin.
The bobbin will then rotate counter clockwise when pull ing out the thread. Replace the cover It. Pull the thread to the left to cut it 2. Only ace a metal presser Jon! To ensure you will get a quality needle, we recommend needles of system ThSII, The needle package included with Platinum 50 contains needles of the most used sizes for sewing in v.. A Universal Needles These needles are used for sewing in all woven fabrics, The needle point is designed to penetrate between the threads of the fabric so the fabric will not be damaged.
B Stretch Needles These needles are used frw sewing in knit and stretch fabrics. The stretch needle is marked yellow and has a rounded point. The jeans needle is marked blue and has an extremely sharp point to facilitate the penetrating of the fabric. Changing the Needle I Loosen the screw in the needle clamp with the screwclri er. A damaged needle b can cause skipped stitches, breakage of needles or snapping of thread. This foot is used mainly for straight stitching and zigzag stitching with a stitch length longer than 1.
The tunnel at the bottom of the foot is designed to feed smoothly over the stitches. The two tunnels on the bottom of the foot ensures a sm x th feed over the buttonhole columns.
Blind Hem Foot 0 This foot is used for blind hem stitches. The inner edge of this foot guides the fabric. The bottom of the toot is designed to ride along the hem edge.
This makes it easy to sew on both sides of the zipper. Edging Footj This foot is used for overcasting, seam and overcasting. D and 5. Stitches form over the pin which pre vents puckering at the edge of the fabric.
Changing the Presser Foot I 2 Make sure that the needle is in the highest position. Pull the presser hx t towards you. Line up the cr ss pin m the toot with the gap in the presser foot ankle. Press ba k until the foot snaps into place. The higher the number the more pressure the foot puts on the fabric Knit and solt fabrics should be sewn at lower pressure. Presser Foot Lever b The presser toot is raised and lowered with the presser foot lever. The presser foot must be lowered when sewing.
By raising the presser foot lex er and then press it upwards, the lift height of the presser foot can be raised to extra height in order to slide thick proiects under the toot. You can adjust the top thread tension for special fabrics and or techniques. To adjust. The higher the number the higher the tension. When sewing buttonholes and decorative stitches set thread tension to around 3.
When ropstitching with a coarse thread in thick fabric, increase the tension to Correct and incorrect thread tension To understand the correct thread ten sion, sew a few sample zigzag stitches at different settings. I Begin with a tension that is t x loose, i. Make a few tests on a scrap piece of the fabric you are going to sew and check the tension.
II In. The feed teeth will raise as v u hegin to sew. STOP is cancelled when you touch the button again or by selecting a new stitch. The stop-. The sideways setting of the stitch plate the hook cover in relation to the feed dog The height of the hook, old hook model The height of the hook,.
The timing of the hook in relation to the needle The needle height Feed dog height Threading device Its mentioned in the manual guide. View the manual for the Husqvarna Platinum here, for free. This manual comes under the category Sewing machines and has been rated by 2 people with an average of a 7. This manual is available in the following languages: English.
Below, you will find the most frequently asked questions about the Husqvarna Platinum Is your question not listed? Ask a question. Jules, No comments 0.
Set needle to stop up or down. For Platinum , tap the foot control to place the needle in down position. Touch reverse to sew any stitch in reverse for a lockstitch and tie off.
Touch reverse twice for continuous reverse. Convenient up-front threading, bobbin winding and placement, free arm, all settings at your fingertips with simple function buttons. One piece aluminium casting is lightweight yet strong, long lasting and prevents vibration. The large foot control allows comfortable sitting position. Store your bobbins, accessory feet, needles and more, right at your fingertips. The new extended working area facilitates working with larger projects.
0コメント